If you find this free website useful – why don’t you support this with a donation? It is easy…. read more ….
I have just finished setting up Varnish on my test server that uses Webmin/Virtualmin, with Apache on Centos.
It has been a little bit of a voyage of discovery but I think I have cracked it. Much of what I have here is based on many other blogs and forums. In essence once you know how its easy, but there are a few pit holes to watch for in Virtualmin/Webmin, as editing the underlying httpd.conf file isn’t the way to go.
The main steps are
- Get Varnish
- Set up the Varnish control file
- Modify the Apache virtual hosts port number
- Restart the servers
- Tidy up Virtualmin server templates and make sure that Varnish runs on boot / restarted with Apache
and you are done. My experience is on a Centos server, I’m sure that the process is the same on Ubuntu except the details of some of the linux level commands and file locations
1. Get Varnish
The easy way – from a repository
yum install varnish
2. Set up the Varnish control file & process defaults
In essence to get up and running this is simply putting the port and IP address that Apache will be listening on. Normally Apache listens on the http port 80, but as Varnish sits in front of Apache, Apache and Varnish will listen on 80 apache has to move – the ‘default’ documentation moves Apache to 8080.
Some people write that they can set it up with Apache listening on 127.0.0.1:80 and Varnish on myexternalIP:80 but I couldn’t get this to work and wasted much time trying to work out where the conflict comes from. If you don’t want to waste time stick to 80 and 8080.
The default.vcl is in etc/varnish
There are a lot more advanced VCL things that you might have to do, like excluding some virtual hosts, and passing through the originators IP address (that Varnish looses as it is a proxy) I’ll cover them in my ‘advanced’ VCL musing in a later post.
You may will need to go into /etc/sysconfig/varnish and set the listen port
3. Modify the Apache configuration to use 8080
All the advice points to updating /etc/httpd/conf/httpd.conf but if you are running Virtualmin/Webmin stop – don’t do that.
You have to modify things via Virtualmin or you will get problems later.
It took a while to find
Virtualmin>[server]>Server Configuration>Change IP address and change the ‘New HTTP Port’ from 80 to 8080. Do this for every existing virtual server
If you have a lot, then you can do this at command level, I wrote this script that goes through all virtual server and changes the port to 8080
for dom in $(virtualmin list-domains –with-feature web –name-only); do virtualmin modify-web –domain $dom –port 8080 done
You then just need to make sure that apache isn’t also listening on port 80.
Go to Webmin>Servers>Apache Webserver, scan down the list of existing Virtual Servers they should all be 8080, the switch to the Global configuration tab > Networking and Addresses, under ports if the is an entry with 80 remove it (none and blank) and save, port 80 shouldn’t be mentioned here at all.
4. Restart The Servers
Sounds simple. I tend to prefer stopping and starting servers at command level. You just need to make sure you stop apache, start varnish and then start apache
service httpd stop service varnish start service httpd start
If httpd doesn’t start then its because it is still listening to post 80, or you didn’t change the varnish default.vcl from 80 to 8080
Check you sites are running!
You also might want to see if varnis is actually running and doing something – a couple of command line commands to run woudl be varnishlog and varnishstat. I might post a bit more about mnitoring when I get more familiar with it.
5. Tidy up Virtualmin server templates and make sure that Varnish runs on boot / restarted with Apache
When you create new virtual servers it uses a server template, and if you don’t change the values you will create new virtual servers on port 80 which will create issues.
Virtualmin>Server Templates> edit each template / template section = Apache website, change Port number for Virtual Hosts to 8080
You need to make sure that Varnish start on reboot too, so
Webmin>System>Bootup and Shutdown
scroll down to find Varnish, edit and set it to start on boot
And you will also need to ensure that Varnish is restarted after you restart Apache for any reason (well you may get away with not, but I think it is safer)
follow the top link to module config and the pull down, system configuration and modify the command to start Apache from /etc/rc.d/init.d/httpd start to /etc/rc.d/init.d/httpd start;/etc/init.d/varnish restart
and the same for the command to apply after configuration.
That should do it!
references / sources
In my voyage of discovery I referenced these items the most
http://blog.nexcess.net/2012/05/21/installing-varnish-for-your-magento-store-on-centos-6/ despite being about Magneto, this well written resource cover a lot of Centos setup in a simple and informative way. Watch out, don’t just cut and paste as this blog has converted quotes into html format.
https://www.varnish-cache.org/docs/3.0/ is the official Varnish documentation which is fine, but it doesn’t help too much beyond the basic setup, worth reading through
http://ocaoimh.ie/2011/08/09/speed-up-wordpress-with-apache-and-varnish/ this is a Ubuntu based post, focusing on WordPress and uses the local host sharing 80 port concept, this actually wasted a lot of time for me. I am also a bit suspect of the wordpress based vcl, but I did base my vcl on some of it.
https://www.varnish-cache.org/trac/wiki/VCLExamples has VCL examples, and is a bteer place to get to understand the VCL options and there are some user contributed WordPress VCls which may be a better way of going than the above.
13 responses to “Setting up Varnish with Virtualmin – Centos in 5 steps”
Gee I wish I’d found this article a few days ago. Would have saved me the same grief since I’m not a SysAdmin 🙂
Now to figur out why switching to fcgid in VirtualMin consumes twice the memory. Maybe I’ve got some double up running or something.
Nice summary, mate
Just wanted to say thank you for taking the time to write this up as I have been struggling.
About to launch in and try again.
This is a great help, thanks for it. Just a side note for anyone using debian like me: the default configuration for varnish on debian is on /etc/default/varnish and not on /etc/sysconfig/varnish as on CentOs.
Very useful, thank you!
Why did you remove the virtualmin script to batch change the ports apache listens on?
sorry, i got confused. the article which contains the script is /www.tienle.com/2013/10-08/setting-varnish-with-virtualmin-centos-5-steps.html
i have multiple vhosts in different IPs in the same physical server. i’m trying to figure out the “backend default” syntax in default.vcl
Was the article removed? I don’t see the 5 steps.
Your HTML reformatter reformatted your virtualmin shell code example. Try instead:
for dom in ($virtualmin list-domains –with-feature web –name-only); do
virtualmin modify-web –domain $dom –port 8080
Leave a Reply to Alan Cancel reply